Adhesive protection for the upper triple tree clamp, specific model for the following Honda CBF 500 and  Hornet 600 1998 - 2004 Will fit on CBF 600 and Hornet CB 600 from 1998 to 2004 by recutting the protection at risers' level Color: Carbon 

Pair of license plate LED lights. Mounted on a M5 integrated threaded screw (diameter 5 mm) for a direct and discreet installation on the license plate holder.   Sold by pair only.

Mounting bracket and adaptor for rearview mirrors, universal model for all handlebars with a 22mm external diameter. Available with 8 mm or 10 mm screw thread (M8 or M10), in normal / classic thread (not inverted). Sold per unit. ...

Screw and cage nut in anodised aluminum. Sold per unit. Various colors available.

Universal cable clutch perch, sold with its aftermarket clutch lever. Adaptation guaranteed on all handlebars with an outer diameter of 22mm. 

Turn signals spacers adapters in plastic, specific for many HONDA , some TRIUMPH , KAWASAKI . These adapters can also adapt on other models. 1 set of 4 spacers adapters is necessary for 1 pair of turn signals (2 adapters per turn indicator)

Front LED headlight. Round adaptable model. Measures : Diameter : 7 inch (17,78 cm) Profondeur : 3,74 inch (9,5 cm) LED bulbs included in the font light, 3 pins connector similar to H4 ones that can be found on nearly all round headlights equipped naked motorbikes.

Complete kit including : an adaptable aluminum license plate holder + a small tail light (position light / brake light / license plate light).   Adaptable model, check measurements on the last picture to make sure it will fit your needs or project.

Pair of anodised aluminum fork pre load adjusters. Available diameters : 14 mm , 17 mm , 19 mm , 22 mm

Universal mounting bracket in steel for round headlights. This model will perfectly fit and adjust without any modification on all forks with a diameter between 33 mm to 43 mm. Sold by pair.

Pair of universal rubber and anodised aluminum handlebar grips with an internal diameter of  22 mm  on the left side (clutch) and  24 mm  on the right side (throttle).   Measures : Length: 120 mm (+ 13 mm with end caps) Depth:...

Aftermarket rear brake fluid reservoir kit including the plastic reservoir + the anodized aluminum cap. Universal model. To avoid mistakes, we invite you to check the type of fastening of your original reservoir before ordering. Height: About 45mm Width: ...

Pair of anodized aluminum bar end plugs, available in several colors. Universal flat model, with a discreet offset.   Fits on all handlebars with an internal diameter of 14mm or 18mm (adapters provided). These handlebar caps can also be installed on handlebars with an integrated 6mm threaded spot (6 mm screw provided)....

Anodized aluminum passenger hand grip, installation on fuel tank’s cap. Specific for numerous HONDA models. Available in different colors, hardware included. CAUTION : if you plan on mounting it on a 1100XX or 1000RR 2012 + you will need some spacers to rise the hand grip. Without these spacers, your passenger may not have enough space to slip his or her fingers and to...

Pair of universal LED turn signals in plastic with 5 SMD  LEDs  on the front, and 3 SMD LEDs on the rear side, both in orange.

Cable clutch perch, High End model in anodised aluminum. Universal for all the motorcycles equipped with a cable clutch. Will fit on all handlebars with a 22mm outer diameter. Sold with an anodised lever, to be selected among : - A short or long clutch lever (no additive cost) - Adjustable in length and foldable in case of a fall (+10€ additive...

Relax cruise control throttle grip for right side handlebar grip. Made in plastic, it will easily install directly on your throttle grip and will allow you to relax your wrist during long journeys. Universal model, will fit on nearly all accelerator grips.

Universal mechanical watch, to be installed on all handlebars with an outer diameter of 22 or 25 mm. Check the available space on your handlebars to make sure you can install it. Measures : Outer diameter : 45mm Height (above handle-bars) : 12mm, the rest will be integrated into the handle bars  Battery not included.

Motorbike tubular and universal insurance slip or tax disc. Length of the tube : 6 cm Diameter : 2.3 cm Diameter of the mounting hole : 0.8 cm

Pair of universal handguards, various colours available. Aluminum base with an ultra-hard plastic coating for an optimal shock-resistance.  Fit on all handlebars with an external diameter of 22 mm or 28 mm and an internal diameter of 14 mm, 18 mm or threaded for M8 screws (8 mm diameter...