Kit of raising clip ons clamps + handlebar tubes  (right AND left clip ons) designed for 50mm diameter forks, consisting of a pair of clamps and a pair of anodised CNC aluminum tubes.    MEASUREMENTS (CLAMPS)  : Riser height : 35 mm Clamp width: 31,9 mm Clamp total height :...

Steel Wheel block / Paddock wheel chock for motorbike. To be installed on a trailer, in a Van, on a lifting platform, etc…   Suitable for all the front wheels from 15 to 21 inches.   Sold such as shown in the pictures.

Rear footrest brackets (right and left bracket), aftermarket model based on the OEM, specific for the following models:    <tr...

Pair of rearview mirrors (left AND right mirror) in anodised aluminum.    This oval model can install in different manners : bar-end or directly on the handlebar itself.   CAUTION: These bar end mirrors are not compatible with a majority of KAWASAKI OEM handlebars.   Please read the description below to check installation possibilities and advices....

LED Taillight with integrated turn signals, specific model for  Triumph :    <tr...

Pair of clip on handlebars (right AND left clip ons) designed for 50mm diameter forks, consisting of a pair of clamps and a pair of anodized CNC aluminum tubes.    Dimensions: Length of the tubes: 30 cm Outside diameter of the tubes: 22 mm Tube’s inner diameter : 16mm Angle of...

Cable clutch perch, High End model in anodised aluminum. Universal for all the motorcycles equipped with a cable clutch. Will fit on all handlebars with a 22mm outer diameter. Sold with an anodised lever, to be selected among : - A short or long clutch lever (no additive cost) - Adjustable in length and foldable in case of a fall (+10€ additive...

Protection pads set including : one slider for fork and one slider for swingarm, specific to the TRIUMPH listed hereafter.   Note  : pictures accurately display the kit, as you will receive it. Only the shaft rod can, in some case, slightly change depending on...

Timing chain, OEM style, high quality, specific for TRIUMPH .  You will find the motorcycles compatibility list below.   Number of links : 126 Thickness : 9 mm    Replaces the following timing chains : T1142126 / T1140768

Pair of rearview mirrors with integrated LED turn signals. Universal model for all naked motorcycles for which the mirrors fastenings are threaded rods (10mm).   Will require an adapter for the right mirror on YAMAHA motorcycles, and for all motorbikes' models which have a reversed thread fastening mirror. 

Engine cover protection crash pad specific for the following TRIUMPH models :       <tr...

Flat handlebar in anodised machined aluminum. Universal model.    Outer diameter at the handlebar’s end: 22,2 mm Outer diameter in the center of the handlebar: 28,6mm (often indicated as 28 mm) Inside diameter: 14 mm, not threaded Weight : 630 gr    <p...

Quick release (1/4 turn) gas cap in anodised aluminum, specific for tmany TRIUMPH  models (complete compatibility list available below).   Sold with a spare seal and the necessary hardware.     IMPORTANT : your original gas cap must look like the one below...

Rear foot-pegs for many  TRIUMPH  models. You will find the motorcycles compatibility list below.    The foot rests are sold by pair (left AND right footrest) with specific fastenings in order to be installed without any modification on the motorcycle models indicated in the listing.   Good to know...

Front foot-pegs for many  TRIUMPH  models. You will find the motorcycles compatibility list below.    The foot rests are sold by pair (left AND right footrest) with specific fastenings in order to be installed without any modification on the motorcycle models indicated in the listing.   Good to know...

Pair of universal risers in anodised machined aluminum, suitable for all motorcycles with a 28 mm diameter handlebar.      Height of the riser :  25  mm Offset : 20 mm        Sold by pair. Hardware included.

Pair of rearview mirrors (left AND right mirrors) in machined anodised aluminum and in plastic. Sold per unit or by pair, different colors available, necessary hardware included. Will fit on naked and faired motorcycles. Caution : if the installation is done on the front fairing, you will need adapters to mount these mirrors (adapters proposed...

Lever guards made of anodized aluminum. Universal model with fasteners adaptable to all handlebars with an inner diameter of 14 or 18 mm. The length of the protection is adjustable (see photos), and the end tip reclining. Available in different colors. Sold by pairs only.